Welcome to the bigboi Knowledge Base
Your Source for Expert Advice, Troubleshooting, and Product Information
-
SuckR PRO
- WashR FLO pump is very noisy
- WashR FLO Water is leaking from the pump
- Storage and Transportation of the SuckR PRO
- Why Is My Engine Housing Overheating?
- Why Is the Suction Weakening?
- How to Assemble the SuckR PRO
- How to Service the SuckR PRO
- How to Use the Extraction Function (Kit Sold Separately)
- How to Use the SuckR PRO Vacuum Function (Wet & Dry)
- SuckR PRO Manual
-
WashR PRO
- The WashR PRO has a oil leak
- The WashR PRO motor does not start when switched on
- The WashR PRO When I switch on the unit, the motor hums but does not run
- Wash PRO TSS Version only. The motor starts even with gun trigger is released
- WashR PRO TSS Version only. No water delivery when gun trigger is depressed
- How to Adjust your Spray Pressure on the WashR PRO
- How to maintain your WashR PRO
- How to store your WashR PRO
- The WashR PRO is experiencing a water leak
- The WashR PRO pressure drops during use
- The WashR PRO Pressure fluctuates
- The WashR PRO pump is noisy
- The WashR PRO pump is running but does not reach the working pressure
- There is the presence of water in oil on the WashR PRO
- How to check your oil level before use?
- How to Setup the WashR PRO
- How to Start your WashR PRO
- How to Stop Your WashR PRO
- How to use your Nozzles with WashR PRO
- WashR PRO Manual
- The WashR FLO Motor refuses to start
- WashR FLO Does not reach high enough pressure
- WashR FLO Motor starts up but there is no working pressure
- WashR FLO motor stops
- WashR FLO No detergent present
- WashR FLO Output pressure varies high and low
- WashR FLO Spray wand is leaking
- How to Set Up the WashR FLO
- How to Turn On and Off Your WashR FLO
- WashR FLO Maintenance Guide
- WashR FLO Manual
Table of Contents
How to Set Up the WashR FLO
Table of Contents
Setting up your Bigboi WashR FLO is simple and straightforward. Follow these step-by-step instructions to ensure your pressure washer is ready for use.
Step-by-Step Instructions
-
Insert Hose into Power Gun
- Insert the end of the hose firmly into the power gun.
- Confirm the hose is locked into the power gun by pulling slightly on the hose. The hose is now securely attached to the power gun.
-
Connect High Pressure Hose
- Screw the quick release hose connector onto the water outlet connector.
- Insert the other end of the pressure hose into the hose connector. Ensure the high-pressure hose is properly tightened to prevent it from slipping or popping off when the unit is turned on.
-
Attach Garden Hose Adaptor (Optional Accessory)
- Attach the quick hose adaptor to the end of the garden hose.
- Snap the quick hose adaptor onto the quick connect filter.
-
Connect Power Lance to Power Gun
- Insert the power lance into the power gun, push together, and twist clockwise to lock in place.
- Change the nozzle as needed for different cleaning tasks.
-
Power On the Unit
- Rotate the power switch to the ON (I) position.
- The motor starts only if the trigger of the gun is pulled and shuts off when the trigger is released.
-
Adjusting the Spray
- The nozzle is adjustable to allow you to change the pressure and spray pattern.
By following these steps, you ensure your WashR FLO is set up correctly for optimal performance. If you encounter any issues, refer to our troubleshooting guide or contact our support team for assistance.
Updated on 24 Jun 2024
What are your Feelings?
Thanks for your feedback
- Choosing a selection results in a full page refresh.