Welcome to the bigboi Knowledge Base
Your Source for Expert Advice, Troubleshooting, and Product Information
-
SuckR PRO
- WashR FLO pump is very noisy
- WashR FLO Water is leaking from the pump
- Storage and Transportation of the SuckR PRO
- Why Is My Engine Housing Overheating?
- Why Is the Suction Weakening?
- How to Assemble the SuckR PRO
- How to Service the SuckR PRO
- How to Use the Extraction Function (Kit Sold Separately)
- How to Use the SuckR PRO Vacuum Function (Wet & Dry)
- SuckR PRO Manual
-
WashR PRO
- The WashR PRO has a oil leak
- The WashR PRO motor does not start when switched on
- The WashR PRO When I switch on the unit, the motor hums but does not run
- Wash PRO TSS Version only. The motor starts even with gun trigger is released
- WashR PRO TSS Version only. No water delivery when gun trigger is depressed
- How to Adjust your Spray Pressure on the WashR PRO
- How to maintain your WashR PRO
- How to store your WashR PRO
- The WashR PRO is experiencing a water leak
- The WashR PRO pressure drops during use
- The WashR PRO Pressure fluctuates
- The WashR PRO pump is noisy
- The WashR PRO pump is running but does not reach the working pressure
- There is the presence of water in oil on the WashR PRO
- How to check your oil level before use?
- How to Setup the WashR PRO
- How to Start your WashR PRO
- How to Stop Your WashR PRO
- How to use your Nozzles with WashR PRO
- WashR PRO Manual
- The WashR FLO Motor refuses to start
- WashR FLO Does not reach high enough pressure
- WashR FLO Motor starts up but there is no working pressure
- WashR FLO motor stops
- WashR FLO No detergent present
- WashR FLO Output pressure varies high and low
- WashR FLO Spray wand is leaking
- How to Set Up the WashR FLO
- How to Turn On and Off Your WashR FLO
- WashR FLO Maintenance Guide
- WashR FLO Manual
Table of Contents
How to Use the Extraction Function (Kit Sold Separately)
Table of Contents
The extraction function of your Bigboi SuckR PRO is perfect for deep cleaning tasks. Follow these steps to use the extraction function with the separately sold kit:
Step-by-Step Instructions
-
Fit the Water Pipe
- First, fit the water pipe as shown in Pic.12.
-
Connect the Extractor Hose
- Remove the current vacuum hose.
- Connect the extractor hose and install the spray brush or spray crevice tool.
-
Install the Water Tank
- Install the water tank as shown in Pic.13.
-
Power On the Unit
- Insert the plug into the outlet.
- Press the on/off switch (Pic.1) on the unit.
-
Code Matching for First Use
- When using the XTRACTR KIT for the first time, code matching is required:
- Turn the switch to position 'I' (Pic.9), the SuckR PRO starts working.
- Press the setting button (S) twice (Pic.11), then press V or S on the remote (Pic.14).
- The SuckR PRO will stop when matching.
- After 10 seconds, the remote will work. Note: The remote cannot work during matching.
- Restart the SuckR PRO (press the button 'O', then 'I' again) (Pic.9), and it will work automatically.
- When using the XTRACTR KIT for the first time, code matching is required:
-
Control Vacuum Functions
- Press the “V” button on the remote to control the wet or dry vacuum cleaner function.
-
Control Water Spray Function
- Press the “S” button to start the water spray function. Pressing it a second time will stop the spray pump motor (Pic.14).
-
Turn Off the Unit
- To turn off the unit, select “O” on the main power switch located on the unit (Pic.9).
By following these steps, you can effectively use the extraction function of your SuckR PRO for deep cleaning tasks. If you encounter any issues, refer to our troubleshooting guide or contact our support team for assistance.
Updated on 24 Jun 2024
What are your Feelings?
Thanks for your feedback
- Choosing a selection results in a full page refresh.